APC AXFA11G Uživatelský manuál Strana 71
- Strana / 118
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
IM 01E20C01-01E
7-4
7. OPERATION VIA BRAIN TERMINAL (BT200)
7.2.3 BT200 Screens & Flow Rate
Data Display
Use the following procedure to display flow rate data
on the BT200.
• The display of flow rate data is updated every 5 seconds.
The Flow Rate Screen
will be displayed.
A maximum of three items
of data can be displayed.
The or
key can be used to move
the cursor up and down.
(Note that the key
can be used to move the
cursor to the top of the
next screen.
Press the ( ) key
to return to Menu Screen
(Major Item Parameter
Search Mode).
F0706.EPS
When the BT200 is turned
on, the message “Please
wait ...” is displayed for
several seconds, and then
the screen on the left is
shown.
Press the key.
or
( )
Press the key
to display initial data as
shown on the left.
Press the ( )or
key.
The tag number
specified upon
ordering is found
here.
The Menu Screen (Major
Item Parameter Search
Mode) will be displayed.
If the key is
pressed while A: DISPLAY
is selected by the highlight
bar, the Parameter Screen
(Sub-Item Parameter
Search Mode) will be
displayed.
–––WELCOME–––
BRAIN Terminal
ID:BT200
Check cable connection
and press the Ent key.
UNTIL FEED
MENU
A:DISPLAY
B:EASY SETUP
C:BASIC SETUP
D:TOTAL SET
E:PULSE SET
F:STATUS FUNC
HOME SET ADJ ESC
PARAMETER
01:MODEL
AXFA11-A00
02:TAG NO
FI-1101
03:SELF CHECK
GOOD
OK
PARAMETER
A10:FLOW RATE(
%
)
80.0
%
A20:FLOW RATE
100m3/h
A21:FLW RATE(mA)
16.800mA
DATA DIAG PRNT ESC
OK
ESC
ESC
7.3 Parameter Setting
Using a BT200
This section describes the procedure for setting of
parameters using a BT200.
IMPORTANT
If the power of flowmeter is turned off within 30
seconds after parameters have been set, these
settings will be canceled. Accordingly, please
keep the power on for at least 30 seconds after
setting parameters.
NOTE
Before updating any setting, remember to always
check the data content you want to change as
described in Chapter 6: Parameter Description.
- IM 01E20C01-01E 1
- Contents 2
- CONTENTS 3
- 1. INTRODUCTION 5
- 1.1 Using the Magnetic 6
- Flowmeter Safely 6
- 1.2 Warranty 6
- 1.3 Combination Remote 7
- Flowtubes 7
- 2. HANDLING PRECAUTIONS 8
- 3. INSTALLATION 9
- 2-inch Pipe Mounting 10
- Panel Mounting 10
- 4. WIRING 11
- 4.3 Wiring Ports 12
- IMPORTANT 13
- 4.4 Wiring Connections 14
- Supply Cables 15
- 4.4.4 DC Power Connection 15
- 4.4.5 Grounding 16
- 4. WIRING 17
- Figure 4.4.6 Wiring Diagram 17
- Figure 4.4.7 Wiring Diagram 17
- Figure 4.4.8 Wiring Diagram 17
- BASIC OPERATING PROCEDURES 20
- (3) Display items 21
- (2 seconds or more) 22
- Select “No” 22
- Select “Yes” 22
- 5.2.2 Setting Mode 24
- F0504-2.EPS 25
- F0505-1.EPS 26
- F0506-1.EPS 27
- 6.2 Parameter Lists 29
- 6.3 Parameter List Overview 30
- T0603-2.EPS 31
- 6. PARAMETER DESCRIPTION 32
- T0607-1.EPS 34
- T0607-2.EPS 35
- T0608-2.EPS 36
- T0612.EPS 38
- 6.4 Parameter Description 40
- Setting Function 43
- No execution 43
- No Execution 43
- Execution 43
- Meter factors of flowtube 44
- Flowtube data plate 44
- Converter data plate 44
- F0601.EPS 44
- T0620.EPS 46
- T0621.EPS 47
- T0626.EPS 49
- T0627.EPS 49
- Switching 50
- Parameter setting sequence 51
- F0612.EPS 55
- F0614.EPS 56
- 0.5% 0.5% 58
- 5.6mA(10%) 58
- F0620.EPS 62
- Default setting (Enable) 62
- F0621.EPS 62
- Write protection (Protect) 62
- 6.5 Alarm Functions 63
- 6.5.2 Alarm Selection 64
- T0651.EPS 66
- 7.1 BT200 Basic Operations 68
- T0804.EPS 69
- 7.2 AXFA11 Operation 70
- Using a BT200 70
- 7.3 Parameter Setting 71
- F0707.EPS 72
- F0708.EPS 73
- “FI-1101” to “FI-1201” 74
- F0802.EPS 76
- (Model 275) 77
- 8.2.2 Display 78
- 8.3 Parameters 79
- 8.3.3 Checking for Problems 80
- 8.3.4 Setting Parameters 80
- F0810.EPS 82
- F0814-2.EPS 85
- F0814-3.EPS 86
- AXFA11 : FI-1100 89
- Poll addr 89
- HELP DEL ESC ENTER 89
- F0820-1.EPS 91
- F0820-2.EPS 91
- F0821-1.EPS 92
- Changing Password 93
- 8.3.5 Menu Tree 95
- (continued on next page) 96
- F0823-4.EPS 98
- 9. ACTUAL OPERATION 99
- 100
- F0902-1.EPS 101
- F0902-3.EPS 102
- Now Auto Zero 102
- Executing 102
- 10. MAINTENANCE 103
- 10.2 Setting of Switches 104
- 10.3 Troubleshooting 106
- 10.3.2 Unstable Zero 107
- 10. MAINTENANCE 108
- 11. OUTLINE 109
- Functions 110
- ■ STANDARD PERFORMANCE 111
- ■ NORMAL OPERATING CONDITIONS 112
- ■ ACCESSORIES 113
- ■ MODEL AND SUFFIX CODE 113
- ● Terminal Configuration 114
- ● Terminal Wiring 114
- ■ EXTERNAL DIMENSIONS 115
- Pipe mounting 116
- Surface mounting 116
- ● Dedicated Signal Cable 117
- AXFC-4-L 117
- AXFC-0-L 117
- REVISION RECORD 118
GermanMAESTRO příručky
Seznam GermanMAESTRO produktových deivces obsahuje 25 uživatelské příručky a návody pro 25 modelů v 4 typech zařízení
Komentáře k této Příručce