APC NetworkAIR Rack Air Removal Unit ACF102BLK Instalační manuál

NetworkAIR® Rack AirRemoval UnitACF102BLKInstallation

Installation6 NetworkAIR Rack Air Removal Unit InstallationInstall the fan frame1. With the exhaust vent at the top of the fan frame, align the four c

InstallationNetworkAIR Rack Air Removal Unit Installation 7Install the fan assembly1. Align the lower pin with the hole in the hinge pin bracket on th

8 NetworkAIR Rack Air Removal Unit InstallationOptional ItemsAmerican Power Conversion offers additional products (not included) for the Rack Air Remo

NetworkAIR Rack Air Removal Unit Installation 9OperationStart-up Use the fan speed selector to set the fan speed based on either the wattage output of

Operation10 NetworkAIR Rack Air Removal Unit InstallationConnect the power supply1. Set the fan speed selector to OFF. 2. Using one of the supplied po

OperationNetworkAIR Rack Air Removal Unit Installation 11To check operation of the unit:5. Apply power to the fans by turning the fan speed selector f

Operation12 NetworkAIR Rack Air Removal Unit InstallationTemperature Override in each Fan Speed ModekW mode Exhaust temperature modeRemote modeTemp Ov

OperationNetworkAIR Rack Air Removal Unit Installation 13How to set the temperature overrideThe temperature override switch is recessed inside the spa

Operation14 NetworkAIR Rack Air Removal Unit InstallationHow to set the fans based on temperatureA temperature probe is located in the intake vents of

NetworkAIR Rack Air Removal Unit Installation 15Alarm SettingsThe Rack Air Removal Unit has three LEDs on the front of the door that indicate whether

16 NetworkAIR Rack Air Removal Unit InstallationHow to Communicate Using the A-LinkThe Rack Air Removal Unit can be used with an APC Environmental Man

How to Communicate Using the A-LinkNetworkAIR Rack Air Removal Unit Installation 172. Plug the device into the A-Link “IN” connector.3. Set the fan sp

How to Communicate Using the A-Link18 NetworkAIR Rack Air Removal Unit InstallationTo remotely control the Rack Air Removal Unit: 1. Set the second, t

NetworkAIR Rack Air Removal Unit Installation 19Warranty and ServiceLimited warrantyAPC warrants the Rack Air Removal Unit to be free from defects in

20 NetworkAIR Rack Air Removal Unit InstallationLife-Support PolicyGeneral policyAmerican Power Conversion (APC) does not recommend the use of any of

NetworkAIR Rack Air Removal Unit Installation 21Specifications — ACF102BLK230VAC; 50Hz ElectricalPower source 230VAC; 50HzRated current 4ACompliance V

APC Worldwide Customer SupportCustomer support for this or any other APC product is available at no charge in any of the following ways:• Visit the AP

ContentsRack Air Removal Unit Installation iGeneral Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Introduction . .

ii Rack Air Removal Unit InstallationLife-Support Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20General policy . . .

NetworkAIR Rack Air Removal Unit Installation 1General InformationIntroductionThe American Power Conversion NetworkAIR® Rack Air Removal Unit removes

2 NetworkAIR Rack Air Removal Unit InstallationSafety InformationWarningFor computer-room use only.Install the Rack Air Removal Unit only on racks tha

NetworkAIR Rack Air Removal Unit Installation 3Before You BeginInventoryItem Description QuantityFan assembly1 Exhaust vent1Fan frame1Power cords

Before You Begin4 NetworkAIR Rack Air Removal Unit InstallationTools requirediReceiving inspectionInspect the package and contents for shipping damage

NetworkAIR Rack Air Removal Unit Installation 5InstallationRemove the rear doors1. If necessary, move the rack to allow for at least 30 inches of clea